Skip to main content

Configure Cisco IOS XE Devices

Netwrix Auditor relies on native syslog events for collecting audit data. Therefore, successful change and access auditing requires a certain configuration of native audit settings in the audited environment. Proper audit configuration ensures audit data integrity; otherwise, your change reports may contain warnings, errors, or incomplete audit data.

CAUTION: Exclude the folder associated with Netwrix Auditor from antivirus scanning. See the Antivirus Exclusions for Netwrix Auditor knowledge base article for additional information.

Netwrix Auditor can't push configuration changes to network devices, so configure native audit settings manually on the Cisco IOS XE (Internetwork Operating System XE) device. When you finish, you configure the device with the following settings:

  • You enable the global configuration mode.
  • You enable the logging on option.
  • You enable the logging timestamp option.
  • You set the logging origin-id option to hostname.
  • You set the logging trap option from 1 to 6 inclusive.
  • You set the logging host parameter to the host address of the computer that hosts Netwrix Auditor Server, and the device uses a UDP port (for example, 514) to send messages.
  • You set the logging source-interface option to the interface that sends syslog messages to Netwrix Auditor Server.

To configure your Cisco IOS XE devices, do the following:

  1. Navigate to your Cisco IOS XE device terminal through the SSH/Telnet connection (for example, use PuTTY Telnet client).

  2. Enter the privileged EXEC mode. For example:

    Router> enable
    Password:
  3. Access the global configuration mode. For example:

    Router# configure terminal
  4. Set the IP address of the Netwrix Auditor Server as the logging host parameter, and ensure that the device uses a UDP port to send syslog messages (e.g., 514 UDP port). For example:

    Router(config)# logging host 192.168.1.5 transport udp port 514
  5. Enable time stamps in syslog messages:

    Router(config)# service timestamps log datetime msec show-timezone year
  6. Configure the device to add its hostname to syslog messages:

    Router(config)# logging origin-id hostname
  7. Set the logging trap option from 1 to 6 inclusive. For example:

    Router(config)# logging trap informational
  8. Set the interface that sends syslog messages to Netwrix Auditor Server. For example:

    Router(config)# logging source-interface GigabitEthernet1
  9. Enable logging:

    Router(config)# logging on
  10. Exit the global configuration mode:

    Router(config)# end

Cisco IOS XE Devices​

Review a full list of object types Netwrix Auditor can collect on Cisco IOS XE network devices.

Object typeActionsEvent ID
Configuration- Modified- CONFIG_I - CFGLOG_LOGGEDCMD - CONFIG_NV - LOGGINGHOST_STARTSTOP
Logon- Successful logon- LOGIN_SUCCESS - WEBLOGIN_SUCCESS - WEBSERVER-5-LOGIN_PASSED - PRIV_AUTH_PASS - DOT1X-5-SUCCESS - MAB-5-SUCCESS
- Failed logon- LOGIN_FAILED - QUIET_MODE_ON - WEBUI_LOGIN_FAILED - WEBSERVER-5-LOGIN_FAILED - DOT1X-5-FAIL - MAB-5-FAIL
- Logoff- SYS-6-LOGOUT
Rule- Activated- IPACCESSLOG - PSECURE_VIOLATION - PM-4-ERR_DISABLE - DHCP_SNOOPING_UNTRUSTED_PORT - SW_DAI - STORM_CONTROL-3-FILTERED - STORM_CONTROL-3-SHUTDOWN - FW-2-BLOCK_HOST - UTD_POLICY_DROP_PKT
Session- Successful logon- CRYPTO-5-SESSION_STATUS: Crypto tunnel is UP - IKEV2-5-SA_UP - FLEXVPN_CONNECTION_UP - SSLVPN-5-LOGIN_AUTH_PASSED
- Failed logon- IKMP_BAD_MESSAGE - IKMP_NO_SA - IKMP_CRYPT_FAILURE - NEG_ABORT - SSLVPN-5-LOGIN_AUTH_FAILED
- Logoff- CRYPTO-5-SESSION_STATUS: Crypto tunnel is DOWN - IKEV2-5-SA_DOWN - FLEXVPN_CONNECTION_DOWN - SSLVPN-5-SESSION_TERMINATE
- Read- RECV_CONNECTION_REQUEST
- Modified- SSLVPN-5-UPDOWN
User- Modified- AAA-5-USER_UNLOCKED - AAA-5-USER_RESET - AAA-5-USER_LOCKED - AAA-5-LOCAL_USER_BLOCKED